Admin
Administrator
Experienced User
Posts: 75
|
 |
« on: November 06, 2009, 10:22:13 am » |
|
Hello all,
The new release is posted so I thought I would put out a call for input on new software features. Granted, the wish list already has quite a few suggestions but it never hurts to ask, right?
So, go ahead and post requests here and open it up for discussion.
Thanks!
Curtis
|
|
|
|
|
Logged
|
Huntron Tech Support
|
|
|
Achcee
New Visitor
Posts: 4
|
|
« Reply #1 on: November 11, 2009, 10:51:14 am » |
|
I would like to see a simpler version of the troublesheet report. Right now it can be many pages long.
Maybe show the probe position in the Image view of the board.
Thanks.
HC
|
|
|
|
|
Logged
|
|
|
|
|
AES_Wind
|
|
« Reply #2 on: November 12, 2009, 06:43:46 am » |
|
 I'm still looking for the ability to scan a component from the troublesheet pane. A rescan/scan ability would be really cool! A rescan opens would be cool too. Thank you Master Splinter! Rob
|
|
|
|
|
Logged
|
Support Our Military. GO Navy.
Anytime. Anywhere. From the land, from the air, from the sea.
|
|
|
Admin
Administrator
Experienced User
Posts: 75
|
|
« Reply #3 on: November 12, 2009, 09:45:16 am » |
|
Thanks for the input!
All of the suggestions so far are being considered, especially rescanning opens from the Troublesheet (one I would like to see also) and having a stripped-down version of the Troublesheet report.
Keep the suggestions coming.
Curtis
|
|
|
|
|
Logged
|
Huntron Tech Support
|
|
|
cimbian
New Visitor
Posts: 6
|
|
« Reply #4 on: November 14, 2009, 07:11:29 am » |
|
Curtis,
How about a parallel/perpendicular function for teach?
Set a datum line from a pin grid, pad array or trace on the PCB, then use parallel/perpendicular mode for teaching DIP/SIP/Multi etc. using the datum as 0 degree. This could speed-up manual teach plus reduce correction step time.
Steve.
|
|
|
|
|
Logged
|
English may be a strange language but I can assure you that an empty-head and an open-mind are not the same thing!
|
|
|
Admin
Administrator
Experienced User
Posts: 75
|
|
« Reply #5 on: November 16, 2009, 07:59:35 am » |
|
Curtis,
How about a parallel/perpendicular function for teach?
Set a datum line from a pin grid, pad array or trace on the PCB, then use parallel/perpendicular mode for teaching DIP/SIP/Multi etc. using the datum as 0 degree. This could speed-up manual teach plus reduce correction step time.
Steve.
Hmmm... I think I am going to need a bit of clarification. It this done visually on screen such as "drawing" a line to mark an array of pins? Is it done numerically? Thanks. Curtis |
|
|
|
|
Logged
|
Huntron Tech Support
|
|
|
cimbian
New Visitor
Posts: 6
|
|
« Reply #6 on: November 21, 2009, 12:19:07 pm » |
|
Hi Curtis,
Draw a line along some known reference (pad edges, not pins for example) and set this as a datum (north-south or east-west). Once the datum is set the movements in teach can be set to be either parallel or perpendicular to this line.
This could make teach even faster than it is now.
Steve.
|
|
|
|
|
Logged
|
English may be a strange language but I can assure you that an empty-head and an open-mind are not the same thing!
|
|
|
Admin
Administrator
Experienced User
Posts: 75
|
|
« Reply #7 on: November 23, 2009, 04:43:25 pm » |
|
Thanks for the clarification, Steve. Suggestion duly noted to the next version wish list.
|
|
|
|
|
Logged
|
Huntron Tech Support
|
|
|
cimbian
New Visitor
Posts: 6
|
|
« Reply #8 on: November 26, 2009, 01:33:11 pm » |
|
Curtis,
Another suggestion:
In teach mode with a DIP/SIP/Multi click adjacent pins and have the spacing multiply my the number in the group... Save scrolling all the way to the end of the row... clearly better used on larger pads but nonetheless valid and easily verified by the programmer... again, a faster way to program.
Relies on knowing the alignment of the PCB artwork as in my last suggestion.
|
|
|
|
|
Logged
|
English may be a strange language but I can assure you that an empty-head and an open-mind are not the same thing!
|
|
|
Admin
Administrator
Experienced User
Posts: 75
|
|
« Reply #9 on: November 29, 2009, 10:51:57 am » |
|
Hi Steve,
The plan is to use the "Pin Spacing" field in the Component settings to update the Travel distance automatically when in Teach mode. This way you only need to click the XY travel arrow the direction you wish to move. This is similar to what you suggested.
Thanks.
Curtis
|
|
|
|
|
Logged
|
Huntron Tech Support
|
|
|
cimbian
New Visitor
Posts: 6
|
|
« Reply #10 on: March 01, 2010, 10:50:43 am » |
|
Curtis, could we use a routine to measure the pin spacing in teach... Measure adjacent pads (edge to edge of identically sized pads) and then update the component pin-spacing field?
|
|
|
|
|
Logged
|
English may be a strange language but I can assure you that an empty-head and an open-mind are not the same thing!
|
|
|
Admin
Administrator
Experienced User
Posts: 75
|
|
« Reply #11 on: March 01, 2010, 11:53:17 am » |
|
Hi Steve,
Some sort of on-screen measurement tools have been suggested before and I think they could be useful. I am not sure of the programming impact regarding their use in updating the database (the Pin Spacing in this case) but anything is possible (our favorite saying -- "it's only software").
Thanks!
|
|
|
|
|
Logged
|
Huntron Tech Support
|
|
|
|
