#91

Obsolete Software / Re: Huntron ProTrack I + Scann...

Last post by Al1234 - November 02, 2023, 12:20:19 AM

I remember when I ran loop Cal for my protrack I had a hard time only because I did not know the process.
Are you sure loop Calc ran all the way through.
Once the tests finish and protrack passes all the tests.
Only once all tests are passed the software goes through another process on its own. At the end it write to the protrack. Then it asks to go to hardware setup and select OK.

#92

Obsolete Software / Re: Huntron ProTrack I + Scann...

Last post by jvthorsley - November 01, 2023, 12:15:35 PM

Hi Curtis and Cyberg3n
Fired up my old PC with Windows XP and both Workstation 3.5.4. & 4.2 installed and searched for the file LCSPRO.TXT.
Can't find it.
Cyberg3n when you finish running LOOP CAL does it mention a file name?
If so I can search for that.
I guess if pushed I could connect this PC to my ProTrack through the printer / Centronics cable and run LOOP CALC myself to see what happens.

#93

Obsolete Software / Re: Huntron ProTrack I + Scann...

Last post by jvthorsley - November 01, 2023, 11:22:10 AM

Yes I have it installed on an old PC.
I will fire it up and let you know.

#94

Obsolete Software / Re: Huntron ProTrack I + Scann...

Last post by admin - November 01, 2023, 10:51:08 AM

James, do you still have 3.5.4. installed? Maybe you can locate the LCSPRO file created by that version?

#95

Obsolete Software / Re: Huntron ProTrack I + Scann...

Last post by jvthorsley - November 01, 2023, 10:45:21 AM

Hi
The file LCSPRO.TXT on my Workstation 4.3 Ver. is located here:-
Windows C:\users\public\public documents\huntron hardware files\LCSPRO.TXT
I guess this is the same with Workstation 3.5.4.

#96

Obsolete Software / Re: Huntron ProTrack I + Scann...

Last post by admin - November 01, 2023, 09:13:05 AM

The file that is created when Loop Calc is run (for a ProTrack only) is called LCPRO.TXT. 
If you run the Loop Calc with the ProTrack and ProTrack Scanner connected (Scanner connected to the ProTrack with the RJ45 interface cable, the BNC cables between the ProTrack and Scanner and powered on) then file created is called LCSPRO.TXT.
I do not recall where these files are stored for Workstation 3.5.4 so search you PC for these files to make sure they are created.

#97

Obsolete Software / Re: Huntron ProTrack I + Scann...

Last post by CyberG3N - November 01, 2023, 08:55:26 AM

I completed the Loop Calc process. I restarted Workstation. It asks me to do loop calc again.

#98

Obsolete Software / Re: Huntron ProTrack I + Scann...

Last post by CyberG3N - November 01, 2023, 08:49:20 AM

I perform Loop Calc and restart the workstation. It asks me to do loop calc again

#99

Obsolete Software / Re: Huntron ProTrack I + Scann...

Last post by admin - November 01, 2023, 08:36:02 AM

Using the software with the ProTrack requires the Loop Calc file to run. Perform the Loop Calc in the Workstation diagnostics. When done restart Workstation and try connecting to the ProTrack.

#100

Obsolete Software / Re: Huntron ProTrack I + Scann...

Last post by CyberG3N - November 01, 2023, 07:13:22 AM

I completed the installation.
The error I see now is
Hardware error
Unable to open Loop Compensation data file
Run Loop Calc in Control-Maintenance-Protrack I Diagnostics

I follow this step but I still get the same error.