Recent posts

#31
Out of Production Hardware / Re: Protrack fails volt check
Last post by Al1234 - December 16, 2023, 12:16:27 PM
preformed an Auto Cal it fixed the voltage check failing.
Thank you fetron for sharing that one in previus posts a while back.
Later, I will try to find and put link to that post here.
https://huntron.com/forum/index.php?topic=324.msg1339#msg1339
#32
Out of Production Hardware / Re: Protrack KJ2 EEPROM
Last post by ken - December 15, 2023, 10:39:31 AM
I'm using INTEL chips. I'm blaming programmer now, bought GQ-4X programmer. Result will prove or I'm wasting money again.
#33
Out of Production Hardware / Re: Protrack KJ2 EEPROM
Last post by fetron - December 14, 2023, 11:28:26 PM
Hello!

Try Catalyst flash ic CAT28F001Pi-12B, or CAT28F001PB-12B, or CAT28F001PA-12B.

Or Intel P28F001-B120.

What type of flash ic are you using?

#34
Out of Production Hardware / Re: Protrack KJ2 EEPROM
Last post by admin - December 14, 2023, 03:45:00 PM
I thought that a link to the bin file had been posted on the Forum before but I can't find it. So, here you go!

V3 firmware

I think this is the correct file. Let me know.

Admin
#35
Out of Production Hardware / Protrack KJ2 EEPROM
Last post by ken - December 14, 2023, 12:29:11 PM
Hello guys, looking for any help I can get. I have 3 Protracks KJ2. One of them just doesn't boot up now. Open them up. After switching 20pin DIP EEPROM P28F001B problem moves from one to another. So all is needed to reprogram the chip. I have Genius G540 for this kind of problems. I made copy from working chip. Programed another one, doesn't fix it. OK, I bought another 2 chips, same model, same manufacturer - INTEL. Programmed - OK. But doesn't work. I'm loosing my mind, I know it is this chip. Then I noticed after reading working chip that it all filled with FF. I shows it is EMPTY. Verification shows they are verified - OK.
Does anyone can share with me bin file for that chip? Or direct me what is going on?

Thanks guys.
#36
Out of Production Hardware / Re: Huntron Protrack KJ2
Last post by dogansabanoglu - December 13, 2023, 04:34:41 AM
Hello, I checked the points you mentioned.  All voltages appear normal.
#37
Technical Support Announcements / Huntron Technical Support News...
Last post by admin - December 12, 2023, 08:07:48 AM
The latest Huntron Technical Support Newsletter is out via email to users. For those not on our email list you can read it here:

Huntron Technical Support News December 2023

Happy Holidays to all of the Huntron Users Support Forum peeps!
Cheers!
#38
Out of Production Hardware / Re: ProTrack I, hi Freq, hi ...
Last post by admin - November 30, 2023, 02:47:47 PM
Yes. There are 20 Groups beside SMT, Passive, Factory, TLL, Caps, etc. that can be configured by the user. This is done through the front panel. Press Menu, then Group Edit, then select the Group (Button just below the Menu button) and rotate the encoder until you see Group 20. You can edit this one or any of the other 19 Groups. Use the Name button to change the Group name if you want.
#39
Out of Production Hardware / Re: ProTrack I, hi Freq, hi ...
Last post by Al1234 - November 30, 2023, 11:10:26 AM
Good morning, I have another question regarding the ProTrack (KJ4 or KJ3), setting. Perhaps it needs it's own topic.
The factory default setup has resistance:
Low    54 Ohm
Mid 1  1.24 KOhm
Mid 2  27.6 KOhm

These resistance setting are not selectable through the encoder nub.
Can users set up resistance besides the 13 selectable ones?
#40
Out of Production Hardware / Re: Protrack fails volt check
Last post by Al1234 - November 29, 2023, 09:02:31 AM
Good morning, thank you for your reply.

Looks like I got to do that on a day off.  ;D  ;D
Happy holidays

Thank you so much for the information.