#81

Out of Production Hardware / Protrack I 20 over voltage

Last post by Al1234 - November 04, 2023, 12:17:23 PM

Anyone knows why a protrack throughs error "over voltage" saying press channel A or B. But has to be turned off/on to resume operation again.
There are 2 that are doing this at random but otherwise they work fine it seems..
They are not being used when error happens. But leads are connected to the protrack. Sometimes the unit is on And is working Then I leave the desk for some reason when I come back the error is on the screen.
1 kj3 and the other kj4.
 

#82

Obsolete Software / Re: Workstation 3.5.4 sigAssis...

Last post by fetron - November 03, 2023, 11:29:42 AM

Create a troublesheet.
Then take measurements on several pins and save the measurements.
Then open the saved measurements and go to the View Signature Zoom window.
Here you have to press the Hardware connect button.
Drag the mouse over the signatures and you can measure with the help of SigAssist.
Now you can change pins and ranges.
Drag the mouse over the signatures and you can measure with the help of SigAssist.

Workstation 4 manual in pdf attachment.

#83

Obsolete Software / Re: Workstation 3.5.4 sigAssis...

Last post by Al1234 - November 03, 2023, 09:52:41 AM

On both kj3 and kj4 no capacitor measurements in veiw signature zoom window as well. Diode and resistance measurement are crappy and spotty.

And there is no way of changing the range there.
In view signature zoom window, If I choose hardware / connect / manual then it goes in manual mode where range can be changed. But then measured signature in the manual mode can't be linked to the view signature zoom window. And still sigAssist is no no 😪😓😭

#84

Obsolete Software / Re: Workstation 3.5.4 sigAssis...

Last post by fetron - November 03, 2023, 03:54:11 AM

Do not measure with Sigassist in Workstation Manual mode.

Open the View Signature Zoom window and it will measure everything well.

I don't know why Sigassist Workstation 3.5.4 does not measure when using Manual mode.

#85

Obsolete Software / Re: Huntron ProTrack I + Scann...

Last post by jvthorsley - November 02, 2023, 09:29:21 AM

Hi
Get the Product Manuals Disc from Huntron.
I have Version 3.0 that has the manauls for Workstation 3.5.4. and the ProTrack 10 / 20.
As Curtis Tech Support he should be able to help with that.

#86

Obsolete Software / Re: Workstation 3.5.4 sigAssis...

Last post by Al1234 - November 02, 2023, 08:52:08 AM

Yes,it measure resistance ok. It does some diodes but not as easy as the resistance.

#87

Obsolete Software / Re: Workstation 3.5.4 sigAssis...

Last post by admin - November 02, 2023, 06:23:00 AM

I am not sure of the cause. If you test a resistor do you get a resistance reading?

#88

Obsolete Software / Re: Huntron ProTrack I + Scann...

Last post by CyberG3N - November 02, 2023, 01:58:36 AM

Now I need a user manual for protrack I and Scanner I. The novelty of the device turned out to be too complicated for me. It would be useful to read a user manual.
You will also need a user guide for Workstation 3.5.4.

#89

Obsolete Software / Re: Huntron ProTrack I + Scann...

Last post by CyberG3N - November 02, 2023, 01:53:41 AM

Files I created manually. Then I did the Loop calculation. It works smoothly now. Thank you very much for your interest.

#90

Obsolete Software / Workstation 3.5.4 sigAssist

Last post by Al1234 - November 02, 2023, 12:31:31 AM

Hi all, I am running workstation 3.5.4 with a kj3 and a kj4.
The sidAssist is not reading cap values and the ohm and +/-Vs reading are really crappy.
Plus depending what voltage I have the PtoTrack on, sigAssist always shows a -Vbd value. The higher the voltage the higher -Vbd. Leads are not connected to anything..
See picture.
All picturs are when using a KJ4 unit and it's the same with kj3.